Firmware for m300
  • C++ 77.9%
  • C 20.5%
  • Python 0.6%
  • Shell 0.4%
  • JavaScript 0.2%
  • Other 0.3%
Find a file
2026-07-22 13:18:46 +02:00
.devcontainer 🔨 VSCode + Devcontainer support (#22420) 2023-03-09 02:45:01 -06:00
.github ✅ Small checkout for each test 2025-07-29 13:13:15 -05:00
.vscode 🧑‍💻 Don't Recommend DevContainer (#26348) 2023-10-22 15:44:29 -05:00
.zed 🧑‍💻 Fix Zed LSP setting 2024-10-16 16:23:57 -05:00
buildroot ✅ Small checkout for each test 2025-07-29 13:13:15 -05:00
config 🔖 Moving to bugfix-2.1.x 2022-06-04 01:22:02 -05:00
docker 🔨 Improve Docker local tests support (#25583) 2023-03-28 23:23:27 -05:00
docs 🧑‍💻 Some TMC2240 updates (2) (#27919) 2025-06-14 16:22:29 -05:00
ini Remove bootloader offset from m300 fw 2026-07-20 18:01:16 +02:00
Marlin config: adjust unload lengths 2026-07-22 13:18:46 +02:00
test 🔨 Sim pins / INI cleanup 2024-05-19 23:07:24 -05:00
.aiderignore 🧑‍💻 Ignores for Aider AI 2024-10-29 11:36:41 -05:00
.editorconfig 🧑‍💻 Update .editorconfig settings (#26264) 2023-10-27 19:46:09 -05:00
.gitattributes .bin and .woff are binary 2020-10-29 00:49:18 -05:00
.gitignore 🧑‍💻 Ignores for Aider AI 2024-10-29 11:36:41 -05:00
LICENSE Update more external links (#18819) 2020-07-28 01:04:44 -05:00
Makefile 🧑‍💻 Allow for tests on macOS / Windows 2025-03-27 20:57:17 -05:00
platformio.ini 🧑‍💻 Group HAL/*/eeprom code 2025-04-26 17:21:36 -05:00
README.md Update README.md 2025-08-18 10:31:04 +02:00

Zortrax Logo

Marlin 3D Printer Firmware
Official Zortrax M200 & M300 Fork

GPL-V3.0 License Original Marlin Repository


About This Fork

This is the official fork of Marlin 2.1.x for Zortrax M200 and M300 3D printers. It is based on the MarlinFirmware/Marlin project and maintained for the Zortrax community.


Additional documentation can be found at the Marlin Home Page. Please test this firmware and let us know if it misbehaves in any way.


Serial communication

To connect serial user interface (OctoPrint or other using Raspberry PI or UART converter and PC) you can use debug header on the motherboard. You will need to solder connector by yourself.

Pinout of the DEBUG header described below:

  • NRST
  • GND <--- connect to GND on host
  • TMS
  • TCK
  • TX <--- connect to RX on host
  • RX <--- connect to TX on host
  • NC
  • VCC (marked on mainboard as 3.3V)

Set baudrate to 250000

Caution: if you are going to use debugger (ST-Link), know that any attempt to read or write from/to flash memory will result in mass erase of the flash. It will erase the the bootloader and all the settings, including lifetimer, serial number and hardware version, as flash memory of chip is read out protection enabled at production! If that happens you won't be able to use official firmware anymore!


Configurations

Official configuration files for Zortrax M200 and M300 printers:

License

Marlin is published under the GPL license because we believe in open development. The GPL comes with both rights and obligations. Whether you use Marlin firmware as the driver for your open or closed-source product, you must keep Marlin open, and you must provide your compatible Marlin source code to end users upon request. The most straightforward way to comply with the Marlin license is to make a fork of Marlin on Github, perform your modifications, and direct users to your modified fork.